Indlægget ToolBase Bumper for Single ToolBase blev først udgivet på SetupRobotics.

Indlægget Flutted Rubber for table blev først udgivet på SetupRobotics.

By having the atmospheric pressure applied to the surface of an item and the pressure removed inside the suction gripper a clamping force is generated.

With our large range of vacuum/suction Grippers the opportunities are endless.

There are many advantages using a suction gripper:

• Enormously selection of different types from many sources.
• Low cost
• No adjustments
• Grip directly on item surface. (no space needed for gripper fingers)
• Items can be placed close together.
• Gently handling yet very powerful.

Vacuum generation
The Toolbase uses an industrial standard venturi pump delivering 85% vacuum and a flow of 6 l/min.

Feedback
The ToolBase measures the pressure inside the suction gripper. When the pressure is below a predefined level the ToolBase signals back to the robots an item is grapped.

Pick & Place timing:
This venturi principle of vacuum generation is way faster than electrical motor based vacuum pumps therefore the reaction time is typically a few milliseconds in comparison to the 300 milliseconds or more to what motor based pump uses.
Also at place the ToolBase is fast as a release blow is generated directly into the suction cup. In comparison many electrical suction grippers only releases to neutral pressure resulting in a long delay before the robot can move away after a place.

CASE: Timing cost:
A robot cell handles 1 item every 1 minute for one year at a cell cost of $100/hour and a vacuum/release generation time of 0,5 second the year cost is: $7300
Typical electrical vacuum gripper cost: (365 * 24 * 60 * 0.5) *($100 / (60*60)) = $7300
Typical venturi vacuum gripper cost: (365 * 24 * 60 * 0.1) *($100 / (60*60)) = $1460

Yearly savings: $7300 – $1460 = $5840

*Works only with our ToolBase (need to buy separately)

Indlægget Vacuum Gripper G1/8″, 20mm cup, 26mm extension blev først udgivet på SetupRobotics.

By having the atmospheric pressure applied to the surface of an item and the pressure removed inside the suction gripper a clamping force is generated.

With our large range of vacuum/suction Grippers the opportunities are endless.

There are many advantages using a suction gripper:

• Enormously selection of different types from many sources.
• Low cost
• No adjustments
• Grip directly on item surface. (no space needed for gripper fingers)
• Items can be placed close together.
• Gently handling yet very powerful.

Vacuum generation
The Toolbase uses an industrial standard venturi pump delivering 85% vacuum and a flow of 6 l/min.

Feedback
The ToolBase measures the pressure inside the suction gripper. When the pressure is below a predefined level the ToolBase signals back to the robots an item is grapped.

Pick & Place timing:
This venturi principle of vacuum generation is way faster than electrical motor based vacuum pumps therefore the reaction time is typically a few milliseconds in comparison to the 300 milliseconds or more to what motor based pump uses.
Also at place the ToolBase is fast as a release blow is generated directly into the suction cup. In comparison many electrical suction grippers only releases to neutral pressure resulting in a long delay before the robot can move away after a place.

CASE: Timing cost:
A robot cell handles 1 item every 1 minute for one year at a cell cost of $100/hour and a vacuum/release generation time of 0,5 second the year cost is: $7300
Typical electrical vacuum gripper cost: (365 * 24 * 60 * 0.5) *($100 / (60*60)) = $7300
Typical venturi vacuum gripper cost: (365 * 24 * 60 * 0.1) *($100 / (60*60)) = $1460

Yearly savings: $7300 – $1460 = $5840

*Must be mounted on our ToolBases.

Indlægget Vacuum Gripper G1/8″, 30mm cup, 26mm extension blev først udgivet på SetupRobotics.

By having the atmospheric pressure applied to the surface of an item and the pressure removed inside the suction gripper a clamping force is generated.

With our large range of vacuum/suction Grippers the opportunities are endless.

There are many advantages using a suction gripper:

• Enormously selection of different types from many sources.
• Low cost
• No adjustments
• Grip directly on item surface. (no space needed for gripper fingers)
• Items can be placed close together.
• Gently handling yet very powerful.

Vacuum generation
The Toolbase uses an industrial standard venturi pump delivering 85% vacuum and a flow of 6 l/min.

Feedback
The ToolBase measures the pressure inside the suction gripper. When the pressure is below a predefined level the ToolBase signals back to the robots an item is grapped.

Pick & Place timing:
This venturi principle of vacuum generation is way faster than electrical motor based vacuum pumps therefore the reaction time is typically a few milliseconds in comparison to the 300 milliseconds or more to what motor based pump uses.
Also at place the ToolBase is fast as a release blow is generated directly into the suction cup. In comparison many electrical suction grippers only releases to neutral pressure resulting in a long delay before the robot can move away after a place.

CASE: Timing cost:
A robot cell handles 1 item every 1 minute for one year at a cell cost of $100/hour and a vacuum/release generation time of 0,5 second the year cost is: $7300
Typical electrical vacuum gripper cost: (365 * 24 * 60 * 0.5) *($100 / (60*60)) = $7300
Typical venturi vacuum gripper cost: (365 * 24 * 60 * 0.1) *($100 / (60*60)) = $1460

Yearly savings: $7300 – $1460 = $5840

*Must be mounted on our ToolBases.

Indlægget Vacuum Gripper G1/8″, 50mm cup, 26mm extension blev først udgivet på SetupRobotics.

*Mount on wall/machine frame – use it with our Reposition mobile clamp male for wheels set

Indlægget Reposition Stationary Wall Female blev først udgivet på SetupRobotics.

*Mount on the Wheel set

– use it with our Reposition mobile female sets (you need to buy wheel set and robot stand separately)

Indlægget Reposition Mobile Clamp Male blev først udgivet på SetupRobotics.

You can add a flutted rubber (check RM-FLRU) to the set.

Indlægget Tray blev først udgivet på SetupRobotics.

This small adapter make it possible to mount our tools bases on this small cobot.

Indlægget Dual ToolBase TM5 adapter blev først udgivet på SetupRobotics.

Indlægget Dual ToolBase UR10 addapter blev først udgivet på SetupRobotics.